Category:35HD-DUAL-NAS-E

From MRT Wiki

Jump to: navigation, search
35HD-DUAL-NAS-E (Giga NAS)
CPU ARM 9, 300MHz
CHIPSET Storlink Gemini SL3512c2 using 1.5W of power
RAM Two 32Mb x 16 333MHz DDR
Flash ROM 16MByte Parallel NOR Flash
Other
NIC 1000/BASE-TX/100BASE-TX/10BASE-T
USB ver 2.0 (for Print server )
internal HDD
SATA/IDE Controller Two SATA slots and one dual channel PATA
Drive Capacity 2TB (2x1TB)
Fan

The 35HD-DUAL-NAS-E is an improved version of the 35HD-DUAL-NAS with 50% faster processor, better ethernet, better USB, native SATA and PATA support and much improved drive capacity due to its use of the Gemini chipset instead of the older Centroid. Other products using this chipset (with very similar features) can be found here.

Contents

Firmwares

Official firmwares:

Unofficial firmwares:

Pictures

PCB pictures

Bootloader log 

Storlink SL351x Boot Loader [Linux], version 1.1.3_P16M_RG08
Built by linux, 15:50:42, Jul  6 2007
Processor: SL3512c2
CPU Rate: 300000000
AHB Bus Clock:150MHz    Ratio:2/1
MAC 1 Address: 00:50:C2:11:11:11
MAC 2 Address: 00:50:C2:22:22:22
inet addr: 192.168.0.200/0.0.0.0
Set LED 4 as off!!
End of set LED!!
Set LED 5 as on!!
End of set LED!!
==> enter ^C to abort booting within 3 seconds ......

Bootloader flash partitioning scheme 

Name              FLASH addr           Mem addr    Datalen     Entry point
BOOT              0x30000000-30017F97  0x00000000  0x00017F98  0x00000000
FIS directory     0x30FE0000-30FFFFFF  0x30FE0000  0x00001400  0x00000000
Kern              0x30020000-3031FFFF  0x01600000  0x0016FDD4  0x01600000
Ramdisk           0x30320000-3091FFFF  0x00800000  0x001F6633  0x00800000
Application       0x30920000-30F1FFFF  0x00000000  0x0041308F  0x00000000
CurConf           0x30F40000-30FDFFFF  0x00000000  0x000A0000  0x00000000
VCTL              0x30F20000-30F3FFFF  0x00000000  0x00020000  0x00000000


/proc/mtd: 

dev:    size   erasesize  name
mtd0: 00020000 00020000 "RedBoot"
mtd1: 00300000 00020000 "Kernel"
mtd2: 00600000 00020000 "Ramdisk"
mtd3: 00600000 00020000 "Application"
mtd4: 00020000 00020000 "VCTL"
mtd5: 000a0000 00020000 "CurConf"
mtd6: 00020000 00020000 "FIS directory"

Linux startup log

For G5S52256208 firmware: 

Linux version 2.6.15 (root@localhost.localdomain) (gcc version 3.4.4) #180 Wed Jan 16 10:19:05 CST 2008
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: GeminiA
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
  DMA zone: 16384 pages, LIFO batch:3
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
Built 1 zonelists
Kernel command line: root=/dev/ram0 rw console=ttySL0,19200 initrd=0x00800000,16M ramdisk_size=16384 mem=64M
PID hash table entries: 512 (order: 9, 8192 bytes)
Bus: 150MHz(2/1)
sl2312 console setup :
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 43836KB available (3255K code, 1172K data, 104K init)
Calibrating delay loop... 262.14 BogoMIPS (lpj=1310720)
Mount-cache hash table entries: 512
*** Page_chain_cachep Init!***
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 16384K
NET: Registered protocol family 16
PCI: bus0: Fast back to back transfers disabled
sl2312_pci_map_irq : slot = 0  pin = 1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initial RAID Descripter...
XOR:tx_desc = ffc00000
XOR:rx_desc = ffc01000
XOR:tx_desc_dma = 0178f000
XOR:rx_desc_dma = 01790000
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/O].
SGI XFS with ACLs, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Real Time Clock Driver v0.10
Gemini Gpio init
Register Gemini Power control
Storlink CIR Initialization
Watchdog Timer Initialized
ttySL0 at MMIO 0x42000000 (irq = 18) is a SL2312
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
VSC-switch not found

Reboot
SL351x Giga Ethernet driver 0.1.5 built at Jan 16 2008 10:16:46
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide 0: physical = 63000000, virtual = c4800000, irq = 4
    ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide 1: physical = 63400000, virtual = c4802000, irq = 5
    ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
MASTER not exist
hdd: SAMSUNG HD103UJ, ATA DISK drive
hdd speed:U6 (66MHz)(0x46)
ide1 at 0xc4802020-0xc4802027,0xc4802036 on irq 5
hdd: max request size: 1024KiB
hdd: 1953525168 sectors (1000204 MB) w/32767KiB Cache, CHS=65535/255/63
hdd: cache flushes supported
 hdd: hdd1 hdd2 hdd3
SL2312 MTD Driver Init.......
SL2312 CFI Flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "SL2312 CFI Flash":
0x00000000-0x00020000 : "RedBoot"
0x00020000-0x00320000 : "Kernel"
0x00320000-0x00920000 : "Ramdisk"
0x00920000-0x00f20000 : "Application"
0x00f20000-0x00f40000 : "VCTL"
0x00f40000-0x00fe0000 : "CurConf"
0x00fe0000-0x01000000 : "FIS directory"
SL2312 MTD Driver Init Success ......
FTC_FOTG2XX : Init FOTG2XX Driver
Init FOTG2xx driver
FTC_FOTG2XX : >>> Found FOTG2XX ...
pFTC_OTG c150e9e0
FTC_FOTG2XX_1 : Init FOTG2XX Driver
Init FOTG2xx driver
FTC_FOTG2XX_1 : >>> Found FOTG2XX ...
pFTC_OTG_1 c150e920
hcd->self.controller c1783400
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX ehci-hcd-FOTG2XX: new USB bus registered, assigned bus number 1
usb_register_bus
ghcd_FOTG2XX hcd c1783400
hcd_irq_For_OTG
ehci->caps->length 10, hcd->regs f6800000 , ehci->regs f6800010
udev->state 1
drivers/usb/host/ehci-hcd-FOTG2XX.c: USB support enabled, EHCI rev 101. 0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FTC_FOTG2XX : >>> +FOTG2XX_get_otg_transceiver
FTC_FOTG2XX : registered host c1783400
OTG2XX act as HOST only (don't need to wait gadget driver)
+(OTGC_Init)
pFTC_OTG->otg.default_a=1
+(OTGC_Init)
pFTC_OTG->otg.default_a=1
OTG_enable_VBUS
FTC_FOTG2XX : >>> Drive VBUS ok...
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
OTG_enable_VBUS
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
ehci otg_set_host status 0
connect_change 1
clear_bit
return set_bit
hcd->self.controller c1520c00
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX-1 ehci-hcd-FOTG2XX-1: new USB bus registered, assigned bus number 2
usb_register_bus
ghcd_FOTG2XX_1 hcd c1520c00
hcd_irq_For_OTG_1
ehci->caps->length 10, hcd->regs f6900000 , ehci->regs f6900010
udev->state 1
drivers/usb/host/ehci-hcd-FOTG2XX-1.c: USB support enabled, EHCI rev 101. 0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
FTC_FOTG2XX_1 : >>> +FOTG2XX_get_otg_transceiver_1
FTC_FOTG2XX_1 : registered host c1520c00
OTG2XX act as HOST only (don't need to wait gadget driver)
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1
OTG_enable_VBUS
FTC_FOTG2XX_1 : >>> Drive VBUS ok...
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
OTG_enable_VBUS
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
ehci otg_set_host status 0
connect_change 1
clear_bit
return set_bit
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   gemini xor acceleration:    47.200 MB/sec
raid5: using function: gemini xor acceleration (47.200 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
ipsec_init : cryptographic accelerator
ipsec tx_desc = ffc14000
ipsec rx_desc = ffc15000
ipsec tx_desc_dma = 0152e000
ipsec rx_desc_dma = 0152f000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 104K
fuse init (API version 7.8)
fuse distribution version: 2.6.3
EXT3-fs: unable to read superblock
EXT2-fs: unable to read superblock
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
isofs_fill_super: bread failed, dev=md0, iso_blknum=16, block=32
NTFS-fs error (device md0): read_ntfs_boot_sector(): Unable to read primary boot sector.
NTFS-fs error (device md0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device md0): ntfs_fill_super(): Not an NTFS volume.
XFS: SB read failed
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs: unable to read superblock
EXT2-fs: unable to read superblock
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
isofs_fill_super: bread failed, dev=md0, iso_blknum=16, block=32
NTFS-fs error (device md0): read_ntfs_boot_sector(): Unable to read primary boot sector.
NTFS-fs error (device md0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device md0): ntfs_fill_super(): Not an NTFS volume.
XFS: SB read failed
Adding 506036k swap on /dev/hdd3.  Priority:-1 extents:1 across:506036k
GMAC-0 Addr 1 Vendor ID: 0x01410cc2
mii_write: phy_addr=0x1 reg_addr=0x4 value=0x5e1
mii_write: phy_addr=0x1 reg_addr=0x9 value=0x300
mii_write: phy_addr=0x1 reg_addr=0x18 value=0x41
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x9200
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x1200
Link Up (0x796d) MII REG 10 = 0x4000
MII REG 5 (bit 5:15) = 0x2f
 100M/Full
Flow Control Enable.
Storlink eth0 address = 7ab4f6000e6b
Enable MAC Flow Control...
GMAC-0 Change MTU = 1454
GMAC-0 Change Status Bits 0x7c-->0x5b


For G5S52256202 firmware: 

Linux version 2.6.15 (root@localhost.localdomain) (gcc version 3.4.4) #155 Fri Oct 26 10:17:15 CST 2007
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: GeminiA
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
Built 1 zonelists
Kernel command line: root=/dev/ram0 rw console=ttySL0,19200 initrd=0x00800000,16M ramdisk_size=16384 mem=64M
PID hash table entries: 512 (order: 9, 8192 bytes)
Bus: 150MHz(2/1)
sl2312 console setup : 
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 43836KB available (3255K code, 1172K data, 104K init)
Mount-cache hash table entries: 512
*** Page_chain_cachep Init!***
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 16384K
NET: Registered protocol family 16
PCI: bus0: Fast back to back transfers disabled
sl2312_pci_map_irq : slot = 0  pin = 1 
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initial RAID Descripter...
XOR:tx_desc = ffc00000
XOR:rx_desc = ffc01000
XOR:tx_desc_dma = 0178f000
XOR:rx_desc_dma = 01790000
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.25 [Flags: R/O].
SGI XFS with ACLs, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Real Time Clock Driver v0.10
Gemini Gpio init
Register Gemini Power control
Power event by Unknow Source 
Storlink CIR Initialization
Watchdog Timer Initialized
ttySL0 at MMIO 0x42000000 (irq = 18) is a SL2312
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
VSC-switch not found
5 seconds to restore default!!
Reboot
SL351x Giga Ethernet driver 0.1.5 built at Oct 26 2007 10:14:57
Reboot
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide 0: physical = 63000000, virtual = c4800000, irq = 4
    ide0: MMIO-DMA , BIOS settings: hda:pio, hdb:pio
ide 1: physical = 63400000, virtual = c4802000, irq = 5
    ide1: MMIO-DMA , BIOS settings: hdc:pio, hdd:pio
hdc: no response (status = 0x80), resetting drive
hdc: no response (status = 0x80)
SL2312 MTD Driver Init.......
SL2312 CFI Flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "SL2312 CFI Flash":
0x00000000-0x00020000 : "RedBoot"
0x00020000-0x00320000 : "Kernel"
0x00320000-0x00920000 : "Ramdisk"
0x00920000-0x00f20000 : "Application"
0x00f20000-0x00f40000 : "VCTL"
0x00f40000-0x00fe0000 : "CurConf"
0x00fe0000-0x01000000 : "FIS directory"
SL2312 MTD Driver Init Success ......
FTC_FOTG2XX : Init FOTG2XX Driver
Init FOTG2xx driver 
FTC_FOTG2XX : >>> Found FOTG2XX ...
pFTC_OTG c1736120
FTC_FOTG2XX_1 : Init FOTG2XX Driver
Init FOTG2xx driver 
FTC_FOTG2XX_1 : >>> Found FOTG2XX ...
pFTC_OTG_1 c17361e0
hcd->self.controller c1783000
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX ehci-hcd-FOTG2XX: new USB bus registered, assigned bus number 1
usb_register_bus
ghcd_FOTG2XX hcd c1783000
hcd_irq_For_OTG
ehci->caps->length 10, hcd->regs f6800000 , ehci->regs f6800010 
udev->state 1 
drivers/usb/host/ehci-hcd-FOTG2XX.c: USB support enabled, EHCI rev 101. 0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FTC_FOTG2XX : >>> +FOTG2XX_get_otg_transceiver
FTC_FOTG2XX : registered host c1783000
OTG2XX act as HOST only (don't need to wait gadget driver)
+(OTGC_Init)
pFTC_OTG->otg.default_a=1 
+(OTGC_Init)
pFTC_OTG->otg.default_a=1 
OTG_enable_VBUS 
FTC_FOTG2XX : >>> Drive VBUS ok...
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
OTG_enable_VBUS 
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
ehci otg_set_host status 0 
connect_change 1 
clear_bit 
return set_bit
hcd->self.controller c0551c00
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX-1 ehci-hcd-FOTG2XX-1: new USB bus registered, assigned bus number 2
usb_register_bus
ghcd_FOTG2XX_1 hcd c0551c00
hcd_irq_For_OTG_1
ehci->caps->length 10, hcd->regs f6900000 , ehci->regs f6900010 
udev->state 1 
drivers/usb/host/ehci-hcd-FOTG2XX-1.c: USB support enabled, EHCI rev 101. 0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
FTC_FOTG2XX_1 : >>> +FOTG2XX_get_otg_transceiver_1
FTC_FOTG2XX_1 : registered host c0551c00
OTG2XX act as HOST only (don't need to wait gadget driver)
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1 
+(OTGC_Init_1)
pFTC_OTG_1->otg.default_a=1 
OTG_enable_VBUS 
FTC_FOTG2XX_1 : >>> Drive VBUS ok...
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
OTG_enable_VBUS 
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close_1()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open_1()(0x30=0x0)
ehci otg_set_host status 0 
connect_change 1 
clear_bit 
return set_bit
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   gemini xor acceleration:    46.800 MB/sec
raid5: using function: gemini xor acceleration (46.800 MB/sec)
md: multipath personality registered as nr 7
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
ipsec_init : cryptographic accelerator 
ipsec tx_desc = ffc14000
ipsec rx_desc = ffc15000
ipsec tx_desc_dma = 0150b000
ipsec rx_desc_dma = 0150c000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 104K
Mounting proc filesystem...
2.6.15
Mounting tmpfs to copy file from flash...
2.6.15
HardDiskBootUp=NO
Boot up from flash
Checking and Mounting filesystem(s) ...
Copy hddapp.bz2 from flash to Ramdisk...
12288+0 records in
12288+0 records out
insmod /lib/modules/fuse.ko
Using /lib/modules/fuse.ko
fuse init (API version 7.8)
fuse distribution version: 2.6.3
2.6.15
2.6.15
2.6.15
SkinnyNAS found, mount /system
EXT3-fs: unable to read superblock
EXT2-fs: unable to read superblock
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: unable to read boot sector
isofs_fill_super: bread failed, dev=md0, iso_blknum=16, block=32
NTFS-fs error (device md0): read_ntfs_boot_sector(): Unable to read primary boot sector.
NTFS-fs error (device md0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover.
NTFS-fs error (device md0): ntfs_fill_super(): Not an NTFS volume.
XFS: SB read failed
mount: Mounting /dev/md0 on /system failed: Invalid argument
SkinnyNAS found, mount /system
mount: Mounting /dev/hda1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/hdb1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/hdc1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/hdd1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/sda1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/sdb1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/sdc1 on /system failed: No such device or address
SkinnyNAS found, mount /system
mount: Mounting /dev/sdd1 on /system failed: No such device or address
mounted device=
2.6.15
Umount tmpfs...
GMAC-0 Addr 1 Vendor ID: 0x01410cc2
mii_write: phy_addr=0x1 reg_addr=0x4 value=0x5e1 
mii_write: phy_addr=0x1 reg_addr=0x9 value=0x300 
mii_write: phy_addr=0x1 reg_addr=0x18 value=0x41 
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x9200 
mii_write: phy_addr=0x1 reg_addr=0x0 value=0x1200 
Link Up (0x796d) MII REG 10 = 0x4000
MII REG 5 (bit 5:15) = 0x2f
 100M/Full
Flow Control Enable.
Storlink eth0 address = 0050c2110137
Enable MAC Flow Control...
2.6.15
Using /lib/modules/rt2561ap.ko
rt2561ap: module license 'unspecified' taints kernel.
Starting syslogd...
Starting inetd...
Starting crond...
Running constructor /usr/sausalito/constructor/00_construct_start
Running constructor /usr/sausalito/constructor/01_construct_network
Running constructor /usr/sausalito/constructor/02_construct_autoip
Running constructor /usr/sausalito/constructor/09_construct_time
Running constructor /usr/sausalito/constructor/10_construct_dhcp
Running constructor /usr/sausalito/constructor/12_construct_syslog
Running constructor /usr/sausalito/constructor/20_construct_disk
Running constructor /usr/sausalito/constructor/20_construct_sata_disk
Running constructor /usr/sausalito/constructor/20_construct_usb_disk
Running constructor /usr/sausalito/constructor/21_construct_disk_crypt
Running constructor /usr/sausalito/constructor/21_construct_raid
Running constructor /usr/sausalito/constructor/25_construct_admin
Running constructor /usr/sausalito/constructor/26_construct_grp_passwd
Running constructor /usr/sausalito/constructor/27_construct_group
Running constructor /usr/sausalito/constructor/30_construct_guest
Running constructor /usr/sausalito/constructor/89_construct_bt2
Running constructor /usr/sausalito/constructor/91_construct_bonjour
Running constructor /usr/sausalito/constructor/95_construct_upnp
Running constructor /usr/sausalito/constructor/99_construct_stop
Done
Local package initialization:start syslogd
syslogd: Already running.
start crond
start thttpd
GetUDN: rand=65e125be
GetInterfaceName: ethernet interface name=eth0
GetUDN: UDN=65e125be-L121-7607-70aa-050c211137
GetInterfaceName: ethernet interface name=eth0
GetIPaddr: IP address=192.168.0.36
main: HTTP_buf=http://192.168.0.36:80
UPnPCreateMicroStack: UUID=uuid:65e125be-L121-7607-70aa-050c211137
.
GMAC-0 Change MTU = 1480
MAC-0 Change Status Bits 0x7c-->0x5b
UPnPCreateMicroStack: Serial Number=0000001
UPnPCreateMicroStack: UPnP.xml...
<?xml version="1.0" encoding="utf-8"?>
<root xmlns="urn:schemas-upnp-org:device-1-0">
<specVersion>
<major>1</major>
<minor>0</minor>
</specVersion>
Sat Feb  2 14:08:26 CST 2008
nas login:

This category currently contains no articles or media.

Retrieved from "http://mrt.nas-central.org/index.php/Category:35HD-DUAL-NAS-E"
Personal tools
Optware
hosted by
hosted by osuosl.org